The 12F675 - A PIC Microcontroller project guide.

<h1>The 12F675 - A PIC Microcontroller project guide.</h1>

by John Main

<div align=justify>The 12F675 is one of the smallest PIC Microcontrollers - it's a tiny device with 8 pins but it's packed with peripherals and it even has a built in 10bit ADC which can read analogue inputs from 4 pins. It has the following internal peripherals: 1. Two timers. 2. An analogue comparator. 3. 10 bit ADC. It also has an internal oscillator and internal reset circuit. This means the device uses minimal external components to make it work (other devices require an external crystal oscillator). Of course it also has the usual internal programming memory, EEPROM and RAM needed for programming. Ideas for projects: 1. 4 channel volt meter. 2. Multi channel Servo controller. 3. Temperature controller. 4. Inductance meter. 5. Touch lamp. 6. Courtesy light time delay. Note: To get data out of the device you can implement a serial RS232 transmit interface to your PC. Why use it? One reason is that because of its size its easy to put into restricted spaces e.g. for a model aircraft or model trains and it's cheaper than the larger devices. Note: The 12F629 is the same device without the ADC - so it's even more cost effective. So it's useful in designs that you would not normally think of using a microcontroller for instance you could make a touch lamp dimmer - Note using the microcontroller means you can make far better functionality than using discrete hardware (and even change its programming later on). With a lamp dimmer you could have an auto off delay function e.g. if no activity for an hour then turn off. State machines You could also implement a state machine for more complex control of the functionality e.g. pressing once moves to the next dimming level in the current direction while press and hold changes the dimming direction. Using a state machine while not trivial lets you control complex operation which you could not achieve (without a great deal of effort) using discrete hardware - and the advantage of using the microcontroller is that if you get it wrong you just re code your software and test it again. Note: The 12F675 and 12F629 use Flash programming memory i .e. they are re-programmable - you can change their functionality instantaneously with NO re-wiring. The only problems are 1. You need to program the device. 2. You need a programming language. Programming the Device Surprisingly you can program the device using the standard 4 pin PIC serial interface - ICSP (In Circuit Serial Programming) and with careful design you can even connect your programmer to the same pins that your circuit uses. Programming language The programming language normally recommended is assembler and there are good reasons for using assembler - e.g. very fast code and smaller final code size but I would recommend using a high level language such as Basic or C. This is because for assembler you need to work at such a low level that you spend a lot of effort to do trivial tasks and this is better left to the high level language. For the example mentioned setting up and maintaining a state machine would be extremely difficult in assembler but much easier in C. You can find some of these 12F675 pic projects here http://www.best-microcontroller-projects.com/12F675.htm Copyright © John Main 2007 Free to distribute if the article is kept complete. </div>

Article source: <a href="http://www.ArticlePros.com/computers_and_internet/Technology/article-78762.html">ArticlePros.com</a>
 
<table align=center width=550 cellspacing=1 bgcolor=silver cellpadding=5>
<tr bgcolor=antiquewhite>
	<td>
		About the author
		John Main's website http://www.best-microcontroller-projects.com provides microcontroller resources and free projects which are fully documented including schematics and source code. 
		<a href="http://www.best-microcontroller-projects.com" target="_blank" title="will open in new window" class=blue>http://www.best-microcontroller-projects.com</a>				<input type=button class=asubm value="Other articles by John Main" onclick="document.location='http://www.ArticlePros.com/author.php?John Main'" style="height:20px;cursor:hand">
	</td>
</tr>
</table>